Section 1:

Identification of Product & Supplier

Product:

Megapoxy 254 - Part B

(Use in conjunction with Megapoxy 254 - Part A)

Classification:

Hazardous according to criteria of Worksafe Australia

Uses:

Adhesive for civil engineering use.

Supplier:

Vivacity Engineering Pty Ltd

ABN:

78 305 545 664

Street Address:

3 Sefton Road

Thornleigh, NSW 2120, Australia

Telephone:

61 2 9875 3044

Facsimile:

61 2 9875 3665

Emergency Phone:

As above or after hours 61 2 9484 7958 or 0418 112 515

e mail:

info@megapoxy.com

Section 2:

Hazards Identification

Hazard Category:

Xi Irritant

Risk Phrases:

R36/38 Irritating to skin and eyes.

R43 May cause sensitisation by skin contact.

D.G. Class:

Not classified as dangerous goods

Subsidiary Risk:

Nil

Poison Schedule:

S 5

This product is a Schedule Poison S 5 and must be stored, maintained and

and used in accordance with the relevant regulation.

Section 3:

Composition & Information on ingredients

Ingredients:

Name

Cas No.

Proportion

Polyaminoamide

68082-29-1

High

Tris-2,4,6 (Dimethylaminomethyl

Phenol

90-72-2

Low

Other ingredients determined

not to be hazardous

To 100 %

V.High >60, High 30 - 60, Med 10 - 29, Low 1 - 9, V.Low <1

All the constituents of this product are listed on the Australian Inventory of

Chemical Substances (AICS) and National Registration Authority (NRA)

approved active constituents.

Section 4:

First Aid Measures

Poison Information Centres in each State capital can provide additional

assistance for scheduled poisons. (Phone Australia 131 126)

Ingestion:

If swallowed do not induce vomiting. Rinse mouth with water, give glass of

water and seek medical attention.

Eye contact:

Immediately irrigate with copious quantities of water for at least 15 minutes.

Eyelids to be held open. Seek immediate medical assistance.

Skin contact:

Remove contaminated clothing and footwear. Wash skin thoroughly with

water. If swelling, redness, blistering or irritation occurs seek medical

attention.

Inhalation:

Remove victim from exposure to fresh air. If breathing difficulty, apply

artificial respiration and seek medical attention.

Note to Physician:

Treat the patient symptomatically.

Section 5:

Fire Fighting Measures

Extinguishing media:

Water, Foam, Dry chemical powder, Carbon dioxide.

Specific Hazards:

The material is stable under normal conditions. Hazardous polymerisation

can occur on heating. On decomposition gives off carbon dioxide, carbon

monoxide, oxides of nitrogen, volatile amines and ammonia. Wear full

protective clothing.

Fire Fighters:

Wear positive pressure, self-contained breathing apparatus and full

protective clothing.

Section 6:

Accidental Release Measures

Small Spills:

Shut off all possible ignition sources. Wear protective equipment to prevent

skin and eye contamination. Clean with absorbent material like sand, soil,

vermiculite or any other inert material. Avoid contamination of drains,

sewerage and waterways. Collect and seal in properly labelled containers

for disposal as per local council statutory codes.

Large Spills:

Shut off all possible ignition sources. Wear protective equipment to prevent

skin and eye contamination. Clean with absorbent material like sand, soil,

vermiculite or any other inert material. Avoid contamination of drains,

sewerage and waterways. Collect and seal in properly labelled containers

for disposal as per local council statutory codes. If contamination of crops,

waterways, drains or sewerage has occurred, advise Emergency Services

or State Department of Agriculture.

Section 7:

Handling and Storage

Storage:

Store in the closed, original container in a cool ventilated area. Keep

containers tightly closed when not in use. Keep away from explosives, food,

oxidising agents and organic peroxides. This product is a Scheduled Poison

S5 and must be stored, maintained and used in accordance with the

relevant regulations. Avoid from physical damage.

Section 8:

Exposure Controls & Personal Protection

Exposure Limits:

No value assigned for this specific product by the National Occupational and

Safety Commission (Worksafe Australia). However, supplier recommended

Hygiene Standard as under;

TWA STEL Carcinogen Notices

Material

TWA

STEL

Notices

ppm

mg/m3

ppm

mg/m3

Polyaminoamide

N/E*

-

Tris-2,4,6 (Dimethy-

N/E*

-

aminomethy) Phenol

N/E* - No Exposure Standard has been established for this product.

Eng. Controls:

Special ventilation is not normally required due to the low volatility of the

product at normal temperature. However, in the operation of certain

equipment or at elevated temperatures, mists or vapours may be generated

and exhaust ventilation should be provided to maintain airborne

concentration levels below the exposure standards or where no exposure

standard is allocated, as low as reasonably practicable.

Personal Protection:

Use overalls, safety shoes, safety goggles, rubber or chemical resistance

gloves and respirator if required.

Manufacturing,

Avoid skin and eye contact and the inhalation of vapour. Wear overalls,

Packaging &

safety goggles and impervious gloves. Available information suggests that the

Transport:

gloves made from PVC should be suitable for intermittent contact. However

due to variations in glove construction and local conditions, the final

assessment should be made by the user. If inhalation risk exists, wear

organic vapour respirator meeting requirements of AS/NZS 1715 and 1716.

Always wash hands with soap and water before smoking, eating, drinking

or using toilet facilities.

Preparations & use

Repeated exposure may cause allergic disorders. Sensitive workers should

of product:

use protective clothing. Avoid contact with eyes and skin. Do not inhale mist

or vapours. After each day's use, wash gloves, safety goggles and all the

contaminated clothing.

Section 9:

Physical & Chemical Properties

Appearance

:

White paste

Solubility :

Partially soluble in water

Specific Gravity :

1.30 - 1.40 @ 25 DEG. C

Boiling Point :

More than 200 deg. C

Rel.Vapour Density (air=1) :

> 1

Melting Range :

Not established

Vapour Pressure (20o C ) :

Less than 0.01 Pa

Decomposition Temp.(o C ) :

More than 200 deg. C

Flash Point (o C ) :

More than 200 deg. C ( ASTM D 93 )

Flammability Limits (% ) :

Not established

Ph :

Not applicable

Autoignition Temp. (o C ) :

Not available

% Volatile by Volume :

Nil

Section 10:

Stability & Reactivity

Stability:

The product is stable under normal conditions and use.

Section 11:

Toxicological Information

No adverse health effects are expected if the product is handled in

accordance with this Safety Data Sheet and the product label. Symptoms

that may arise if the product is mishandled are:

Acute Effects:

Ingestion:

Harmfull if swallowed. May cause gastrointestinal discomfort and

irritation.

Eye:

Brief contact may cause mild irritation to eyes.

Skin:

Mild irritant and poorly absorbed through the skin. Prolonged and

repeated contact may cause sever irritation and/or dermatitis

Inhaled:

Not hazardous at ambient temperatures. Vapours generated at

elevated temperatures or when inhaled repeatedly may cause

irritation to nose, throat and respiratory tract.

Long Term Effects:

Repeated skin contact and inhalation may result in sensitisation in some

individuals. May cause allergic reaction, dermatitis or asthma like symptoms.

Follow good working practice. Avoid ingestion, inhalation, eye and skin

contact. Wash hands with soap and water before eating, drinking, smoking

or using toilet facilities.

Acute & Chronic

Negative in a battery of mutagenicity assays.

Toxicity:

No evidence of carcinogenicity was observed in long term studies of rats.

No developmental nor reproductive effects in rat and rabbit.

Acceptable Daily Intake ( ADI ) for humans is 0.01 mg/kg/day.

Section 12:

Ecological Information

Avoid contamination of drains, sewerage, creeks and waterways.

Product may be toxic to some aquatic organisms.

Section 13:

Disposal Consideration

Dispose all empty containers as per State & Council Regulation. Do not

dispose near waterways, vegetation and tree roots. Empty containers and

product should not be burned.

Section 14:

Transport Information

UN. No. :

Not Applicable

Shipping Name :

Not Applicable

Class :

Not classified as dangerous goods

Subsidiary Risk :

Nil

Packaging Group :

Not Applicable

Hazchem Code :

Not Applicable

EPG :

Not Applicable

Segregation :

Not Applicable

For road, marine and air transport this product is not classified as dangerous

goods within the context of National and International Transport Regulation.

Section 15:

Regulatory Information

The National Model Regulations for the Control of Workplace Hazardous

Substances [ NOHSC : 10005 (1999)].

The National Standard for the Storage and Handling of Workplace

Dangerous Goods [ NOHSC : 1015 (2001)].

Section 16:

Other information

Date of Preparation :

21.02.11

Date of Revision :

21.02.16

Reasons for Issue :

Five yearly review.

MSDS's are updated frequently. Please ensure you have the current copy.

This MSDS summarises at the date of issue our best knowledge of health

and safety hazard information of the product, and in particular how to handle

and use the product in the workplace. Since Vivacity Engineering Pty Ltd

cannot anticipate or control the conditions under which the product may be

used each user must, prior to usage, review this MSDS in the context to use

and handling of the product in the workplace.

If clarification or further information is needed to ensure that an appropriate

assessment can be made, the user should contact Vivacity Engineering Pty

Ltd. Our responsibility for the product as sold is subject to our standard

terms and conditions, a copy of which is sent to our customers and is also

available upon request.

Approved By:

Frank Taylor

Managing Director

Material Safety Data Sheet
Section 1:	Identification of Product & Supplier
Product:	Megapoxy 254 - Part B
	(Use in conjunction with Megapoxy 254 - Part A)
Classification:	Hazardous according to criteria of Worksafe Australia
Uses:	Adhesive for civil engineering use.
Supplier:	Vivacity Engineering Pty Ltd
ABN:	78 305 545 664
Street Address:	3 Sefton Road
	Thornleigh, NSW 2120, Australia
Telephone:	61 2 9875 3044
Facsimile:	61 2 9875 3665
Emergency Phone:	As above or after hours 61 2 9484 7958 or 0418 112 515
e mail:	info@megapoxy.com

Section 2:	Hazards Identification
Hazard Category:	Xi Irritant
Risk Phrases:	R36/38 Irritating to skin and eyes.
	R43 May cause sensitisation by skin contact.
D.G. Class:	Not classified as dangerous goods
Subsidiary Risk:	Nil
Poison Schedule:	S 5
	This product is a Schedule Poison S 5 and must be stored, maintained and
	and used in accordance with the relevant regulation.

Section 3:	Composition & Information on ingredients
Ingredients:	Name			Cas No.		Proportion
	Polyaminoamide			68082-29-1		High
	Tris-2,4,6 (Dimethylaminomethyl
	Phenol			90-72-2		Low
	Other ingredients determined
	not to be hazardous					To 100 %
	V.High >60, High 30 - 60, Med 10 - 29, Low 1 - 9, V.Low <1
	All the constituents of this product are listed on the Australian Inventory of
	Chemical Substances (AICS) and National Registration Authority (NRA)
	approved active constituents.

Section 4:	First Aid Measures
	Poison Information Centres in each State capital can provide additional
	assistance for scheduled poisons. (Phone Australia 131 126)
Ingestion:	If swallowed do not induce vomiting. Rinse mouth with water, give glass of
	water and seek medical attention.
Eye contact:	Immediately irrigate with copious quantities of water for at least 15 minutes.
	Eyelids to be held open. Seek immediate medical assistance.
Skin contact:	Remove contaminated clothing and footwear. Wash skin thoroughly with
	water. If swelling, redness, blistering or irritation occurs seek medical
	attention.
Inhalation:	Remove victim from exposure to fresh air. If breathing difficulty, apply
	artificial respiration and seek medical attention.
Note to Physician:	Treat the patient symptomatically.

Section 5:	Fire Fighting Measures
Extinguishing media:	Water, Foam, Dry chemical powder, Carbon dioxide.
Specific Hazards:	The material is stable under normal conditions. Hazardous polymerisation
	can occur on heating. On decomposition gives off carbon dioxide, carbon
	monoxide, oxides of nitrogen, volatile amines and ammonia. Wear full
	protective clothing.
Fire Fighters:	Wear positive pressure, self-contained breathing apparatus and full
	protective clothing.

Section 6:	Accidental Release Measures
Small Spills:	Shut off all possible ignition sources. Wear protective equipment to prevent
	skin and eye contamination. Clean with absorbent material like sand, soil,
	vermiculite or any other inert material. Avoid contamination of drains,
	sewerage and waterways. Collect and seal in properly labelled containers
	for disposal as per local council statutory codes.
Large Spills:	Shut off all possible ignition sources. Wear protective equipment to prevent
	skin and eye contamination. Clean with absorbent material like sand, soil,
	vermiculite or any other inert material. Avoid contamination of drains,
	sewerage and waterways. Collect and seal in properly labelled containers
	for disposal as per local council statutory codes. If contamination of crops,
	waterways, drains or sewerage has occurred, advise Emergency Services
	or State Department of Agriculture.

Section 7:	Handling and Storage
Storage:	Store in the closed, original container in a cool ventilated area. Keep
	containers tightly closed when not in use. Keep away from explosives, food,
	oxidising agents and organic peroxides. This product is a Scheduled Poison
	S5 and must be stored, maintained and used in accordance with the
	relevant regulations. Avoid from physical damage.
Section 8:	Exposure Controls & Personal Protection
Exposure Limits:	No value assigned for this specific product by the National Occupational and
	Safety Commission (Worksafe Australia). However, supplier recommended
	Hygiene Standard as under;
	TWA STEL Carcinogen Notices
	Material		TWA		STEL		Notices
			ppm	mg/m3	ppm	mg/m3
	Polyaminoamide		N/E*	N/E*	N/E*	N/E*	-
	Tris-2,4,6 (Dimethy-		N/E*	N/E*	N/E*	N/E*	-
	aminomethy) Phenol

	N/E* - No Exposure Standard has been established for this product.
Eng. Controls:	Special ventilation is not normally required due to the low volatility of the
	product at normal temperature. However, in the operation of certain
	equipment or at elevated temperatures, mists or vapours may be generated
	and exhaust ventilation should be provided to maintain airborne
	concentration levels below the exposure standards or where no exposure
	standard is allocated, as low as reasonably practicable.
Personal Protection:	Use overalls, safety shoes, safety goggles, rubber or chemical resistance
	gloves and respirator if required.
Manufacturing,	Avoid skin and eye contact and the inhalation of vapour. Wear overalls,
Packaging &	safety goggles and impervious gloves. Available information suggests that the
Transport:	gloves made from PVC should be suitable for intermittent contact. However
	due to variations in glove construction and local conditions, the final
	assessment should be made by the user. If inhalation risk exists, wear
	organic vapour respirator meeting requirements of AS/NZS 1715 and 1716.
	Always wash hands with soap and water before smoking, eating, drinking
	or using toilet facilities.
Preparations & use	Repeated exposure may cause allergic disorders. Sensitive workers should
of product:	use protective clothing. Avoid contact with eyes and skin. Do not inhale mist
	or vapours. After each day's use, wash gloves, safety goggles and all the
	contaminated clothing.

Section 9:	Physical & Chemical Properties
	Appearance :		:	White paste
	Solubility :			Partially soluble in water
	Specific Gravity :			1.30 - 1.40 @ 25 DEG. C
	Boiling Point :			More than 200 deg. C
	Rel.Vapour Density (air=1) :			> 1
	Melting Range :			Not established
	Vapour Pressure (20o C ) :			Less than 0.01 Pa
	Decomposition Temp.(o C ) :			More than 200 deg. C
	Flash Point (o C ) :			More than 200 deg. C ( ASTM D 93 )
	Flammability Limits (% ) :			Not established
	Ph :			Not applicable
	Autoignition Temp. (o C ) :			Not available
	% Volatile by Volume :			Nil

Section 10:	Stability & Reactivity
Stability:	The product is stable under normal conditions and use.

Section 11:	Toxicological Information
	No adverse health effects are expected if the product is handled in
	accordance with this Safety Data Sheet and the product label. Symptoms
	that may arise if the product is mishandled are:
Acute Effects:	Ingestion:	Harmfull if swallowed. May cause gastrointestinal discomfort and
		irritation.
	Eye:	Brief contact may cause mild irritation to eyes.
	Skin:	Mild irritant and poorly absorbed through the skin. Prolonged and
		repeated contact may cause sever irritation and/or dermatitis
	Inhaled:	Not hazardous at ambient temperatures. Vapours generated at
		elevated temperatures or when inhaled repeatedly may cause
		irritation to nose, throat and respiratory tract.
Long Term Effects:	Repeated skin contact and inhalation may result in sensitisation in some
	individuals. May cause allergic reaction, dermatitis or asthma like symptoms.
	Follow good working practice. Avoid ingestion, inhalation, eye and skin
	contact. Wash hands with soap and water before eating, drinking, smoking
	or using toilet facilities.
Acute & Chronic	Negative in a battery of mutagenicity assays.
Toxicity:	No evidence of carcinogenicity was observed in long term studies of rats.
	No developmental nor reproductive effects in rat and rabbit.
	Acceptable Daily Intake ( ADI ) for humans is 0.01 mg/kg/day.

Section 12:	Ecological Information
	Avoid contamination of drains, sewerage, creeks and waterways.
	Product may be toxic to some aquatic organisms.

Section 13:	Disposal Consideration
	Dispose all empty containers as per State & Council Regulation. Do not
	dispose near waterways, vegetation and tree roots. Empty containers and
	product should not be burned.

Section 14:	Transport Information
	UN. No. :			Not Applicable
	Shipping Name :			Not Applicable
	Class :			Not classified as dangerous goods
	Subsidiary Risk :			Nil
	Packaging Group :			Not Applicable
	Hazchem Code :			Not Applicable
	EPG :			Not Applicable
	Segregation :			Not Applicable
	For road, marine and air transport this product is not classified as dangerous
	goods within the context of National and International Transport Regulation.

Section 15:	Regulatory Information
	The National Model Regulations for the Control of Workplace Hazardous
	Substances [ NOHSC : 10005 (1999)].
	The National Standard for the Storage and Handling of Workplace
	Dangerous Goods [ NOHSC : 1015 (2001)].

Section 16:	Other information
	Date of Preparation :			21.02.11
	Date of Revision :			21.02.16
	Reasons for Issue :			Five yearly review.
	MSDS's are updated frequently. Please ensure you have the current copy.
	This MSDS summarises at the date of issue our best knowledge of health
	and safety hazard information of the product, and in particular how to handle
	and use the product in the workplace. Since Vivacity Engineering Pty Ltd
	cannot anticipate or control the conditions under which the product may be
	used each user must, prior to usage, review this MSDS in the context to use
	and handling of the product in the workplace.
	If clarification or further information is needed to ensure that an appropriate
	assessment can be made, the user should contact Vivacity Engineering Pty
	Ltd. Our responsibility for the product as sold is subject to our standard
	terms and conditions, a copy of which is sent to our customers and is also
	available upon request.
Approved By:	Frank Taylor
	Managing Director